中兴B700V2Y机顶盒

来自IPTV爱好者
跳转至: 导航搜索

概况

B700V2Y采用博通的7405方案。

B700V2Y内核分析

CFE刷机

网络设置:

ifconfig eth0 -auto
100 MB Full-Duplex (auto-neg)
Device eth0:  hwaddr 00-26-ED-5A-6E-47, ipaddr 192.168.3.128, mask 255.255.255.0
        gateway 192.168.3.1, nameserver 192.168.3.1
*** command status = 0

网络测试:

ping 192.168.3.10
192.168.3.10 (192.168.3.10) is alive
192.168.3.10 (192.168.3.10): 1 packets sent, 1 received
*** command status = 0

刷开机画面:

flash -noheader -offset=0x0 192.168.3.10:mtdblock3.bin flash0.splash
Reading 192.168.3.10:mtdblock3.bin: cfe loading percent: 6%
cfe loading percent: 12%
cfe loading percent: 14%
cfe loading percent: 14%
Done. 4194304 bytes read
Programming...done. 4194304 bytes written
*** command status = 0


-rwxr-xr-x    1 root     root      2097152 Feb  2 06:27 mtdblock0.bin
-rwxr-xr-x    1 root     root      1048576 Feb  2 06:27 mtdblock1.bin
-rwxr-xr-x    1 root     root      2097152 Feb  2 06:27 mtdblock2.bin
-rwxr-xr-x    1 root     root      4194304 Feb  2 06:27 mtdblock3.bin
-rwxr-xr-x    1 root     root      4194304 Feb  2 06:27 mtdblock4.bin
-rwxr-xr-x    1 root     root      2097152 Feb  2 06:27 mtdblock5.bin
-rwxr-xr-x    1 root     root      2097152 Feb  2 06:27 mtdblock6.bin
-rwxr-xr-x    1 root     root      8388608 Feb  2 06:28 mtdblock7.bin
-rwxr-xr-x    1 root     root      8388608 Feb  2 06:28 mtdblock8.bin
-rwxr-xr-x    1 root     root     62914560 Feb  2 06:28 mtdblock9.bin
-rwxr-xr-x    1 root     root     62914560 Feb  2 06:30 mtdblock10.bin
-rwxr-xr-x    1 root     root     20971520 Feb  2 06:39 mtdblock11.bin
-rwxr-xr-x    1 root     root      8388608 Feb  2 06:40 mtdblock12.bin
-rwxr-xr-x    1 root     root     75497472 Feb  2 06:43 mtdblock13.bin

    flash0.data  New NAND flash at 10000000 offset 00000000 size 102400KB    mtdblock11.bin
    flash0.app1  New NAND flash at 10000000 offset 06400000 size 61440KB     mtdblock10.bin
    flash0.app0  New NAND flash at 10000000 offset 0A000000 size 61440KB     mtdblock9.bin
 flash0.kernel1  New NAND flash at 10000000 offset 0DC00000 size 8192KB      mtdblock8.bin
 flash0.kernel0  New NAND flash at 10000000 offset 0E400000 size 8192KB      mtdblock7.bin
flash0.osflags0  New NAND flash at 10000000 offset 0EC00000 size 2048KB      mtdblock6.bin
flash0.osflags1  New NAND flash at 10000000 offset 0EE00000 size 2048KB      mtdblock5.bin
  flash0.config  New NAND flash at 10000000 offset 0F000000 size 4096KB      mtdblock4.bin
  flash0.splash  New NAND flash at 10000000 offset 0F400000 size 4096KB      mtdblock3.bin
   flash0.nvram  New NAND flash at 10000000 offset 0F800000 size 2048KB      mtdblock2.bin
  flash0.macadr  New NAND flash at 10000000 offset 0FA00000 size 2048KB      mtdblock1.bin
     flash0.cfe  New NAND flash at 10000000 offset 0FC00000 size 2048KB      mtdblock0.bin
 flash0.virtual  New NAND flash at 10000000 offset 0FE00000 size 1024KB
 flash0.kreserv  New NAND flash at 10000000 offset 0FF00000 size 1024KB

其他信息

  • CFE启动信息:
BCM74130011
012
K1
K2

K3

K4

K5

Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000005
WC1=FFFFFFE0
RC2=0000001F
WC2=00000035
RC3=00000012
WC3=FFFFFFE0
RC4=00000012
WC4=00000037
NWC=0000000B
RC5=00000005
WC5=0000000B
RC6=0000001F
WC6=0000000B
NRC=00000012
RW=0000001B
WW=00000058
G=00000000 R=00000012 W=0000000B 
BL=00000000
RC1=00000006
RC2=0000001B

BL=00000001
RC1=00000006
RC2=0000001A

BL=00000002
RC1=00000004
RC2=0000001A

BL=00000003
RC1=00000007
RC2=0000001E
3
COPY CODE
A567

BCM97213B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: 2011年 02月 10日 星期四 14:18:28 CST (ken@ZouYongqian)
Copyright (C) Broadcom Corporation.

add a new flash, flash_phys_base=0x10000000, will be reset to 0! 

DDR Freq:      396MHz
CPU speed:     405MHz
Memory Config: 32-bit UMA
Device Tech:   1Gb
Total memory:  256MB
Boot Device:   NAND
Total flash:   256MB

osflags open device flash0.osflags0
osflags open device flash0.osflags1
osflags: get valid osflags partition flash0.osflags1.
osflags checksum ok
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub

CFE initialized.
Starting splash screen.
***************************************************
Found splash image - Width = 1280 Height = 720 splashWidth: 1280 splashheight: 720
***************************************************
 -- replace  splashAddress1 0xae600000 to new offsetNew 0xe600000 
 -- replace splashAddress 0xaf600000 to new offsetNew 0xf600000 

xor = 0
Loader:elf Filesys:raw Dev:flash1.kernel1 File: Options:mem=100M flashsize=256M brcmnand=rescan
Loading: !!!!! UNC read error occurred, while reading from NAND flash
cfe loading percent: 1%
cfe loading percent: 1%
0x80001000/8522120 cfe loading percent: 14%
0x80821988/185996 Entry address is 0x8047f000
TP1 Entry Address at 0x80000ffc = 8047f000
Starting program at 0x8047f000Starting program at 0x8047f000
  • Linux启动信息
<5>Linux version 2.6.18-7.1 (ken@ZouYongqian) (gcc version 4.2.0 20070124 (prerelease) - BRCM 11ts-20090508) #342 SMP Mon Jan 10 09:18:17 CST 2011
Fetching vars from bootloader... OK (E,D,B,C)
Detected 256 MB on MEMC0 (strap 0x235c2812)
CFE EnvVar: SPLASH_PART_STARTAD: 0f400000, SPLASH_PART_SIZE: 00400000
g_board_RAM_size=256MB
**********SKIP_CHECK_BOOTROM: BOOTEDFROMFLASH, Base=10000000, flashSize=256MB
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=1
CPU revision is: 0002a044
FPU revision is: 00130001
Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, linesize 64 bytes.
<6>Synthesized TLB refill handler (23 instructions).
<6>Synthesized TLB load handler fastpath (37 instructions).
<6>Synthesized TLB store handler fastpath (37 instructions).
<6>Synthesized TLB modify handler fastpath (36 instructions).
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
User-defined physical RAM map:
node [00000000, 06400000: RAM]
node [06400000, 09c00000: RSVD]
<5>Reserving 156 MB upper memory starting at 06400000
<7>On node 0 totalpages: 65536
<7>  DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists.  Total pages: 65536
<5>Kernel command line: mem=100M flashsize=256M brcmnand=rescan console=ttyS0,115200 rw
PID hash table entries: 2048 (order: 11, 8192 bytes)
Found MIPS counter frequency: 203 Mhz
Using 202.501 MHz high precision timer.
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 91392k/262144k available (3693k kernel code, 170576k reserved, 904k data, 3724k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
plat_prepare_cpus: ENABLING 2nd Thread...
TP0: prom_boot_secondary: Kick off 2nd CPU...
CPU revision is: 0002a044
FPU revision is: 00130001
Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, linesize 64 bytes.
Synthesized TLB refill handler (23 instructions).
Brought up 2 CPUs
migration_cost=1000
==============================================splash_init
NET: Registered protocol family 16
PCI->SDRAM window size: 512MB
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
brcm-pm: disabling power to USB block
brcm-pm: disabling power to ENET block
brcm-pm: disabling power to SATA block
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
NTFS driver 2.1.27 [Flags: R/O].
JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.
fuse init (API version 7.7)
yaffs Jan  9 2011 10:35:36 Installing. 
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 22) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 66) is a 16550A
serial8250: ttyS2 at MMIO 0x0 (irq = 67) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8704K size 1024 blocksize
loop: loaded (max 8 devices)
brcm-pm: enabling power to ENET block
Broadcom BCM7413 P21 Ethernet Network Device v2.0 Jan  6 2011 15:33:17
Config Internal PHY Through MDIO: Auto-negotiation timed-out
: 10 MB Half-Duplex (assumed)
bcmemac: no PHY detected on EMAC_1, disabling
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
CSLIP: code copyright 1989 Regents of the University of California.
SLIP linefill/keepalive option.
brcm-pm: enabling power to SATA block
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
ata2: SATA max UDMA/133 cmd 0xB0510100 ctl 0xB0510120 bmdma 0xB0510130 irq 42
scsi0 : sata_svw
ata1: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051001c
scsi1 : sata_svw
ata2: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051011c
Broadcom STB NAND controller (BrcmNand Controller)
i=0, CS[0] = 0
brcmnand_probe: CS0: dev_id=20da1095
After: NandSelect=40000101, nandConfig=16152300
NAND Config: Reg=16152300, chipSize=256 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
BrcmNAND mfg 20 da ST NAND02GW3B2C 256MB

Found NAND: ACC=f7ff1010, cfg=16152300, flashId=20da1095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 256MB @00000000
brcmnand_probe: CS0: dev_id=20da1095
After: NandSelect=40000101, nandConfig=16152300
Found NAND chip on Chip Select 0, chipSize=256MB, usable size=256MB, base=0x
brcmnand_scan: chip->pbase=10000000, set to 0 to disable xor!
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
ACC_CONTROL for SLC NAND: f7ff1010, eccLevel=15
SLC flash: ACC_CONTROL = f7ff1010
page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 256MB @00000000
mtd->oobsize=64, mtd->eccOobSize=16
brcmnand_scan:  mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
rescanning .... 
----- Contents of BBT -----
----- END Contents of BBT -----
brcmnandCET: Status -> Deferred
	numchips=1, size=10000000
Creating 14 MTD partitions on "bcm7xxx-nand.0":
0x0000000000000000-0x0000000000200000 : "cfe"
0x0000000000400000-0x0000000000500000 : "nvm"
0x0000000000600000-0x0000000000800000 : "macadr"
0x0000000000800000-0x0000000000c00000 : "splash"
0x0000000000c00000-0x0000000001000000 : "config"
0x0000000001000000-0x0000000001200000 : "osflags0"
0x0000000001200000-0x0000000001400000 : "osflags1"
0x0000000001400000-0x0000000001c00000 : "kernel0"
0x0000000001c00000-0x0000000002400000 : "kernel1"
0x0000000002400000-0x0000000006000000 : "app0"
0x0000000006000000-0x0000000009c00000 : "app1"
0x0000000009c00000-0x000000000b000000 : "game"
0x000000000b000000-0x000000000b800000 : "resource"
0x000000000b800000-0x0000000010000000 : "swap"
usbmon: debugfs is not available
ehci_hcd_brcm_init: Initializing 2 EHCI controller(s)
brcm-pm: enabling power to USB block
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
 - USB h/w setup mode
 - USB power enable set for active LOW mode
brcm-ehci brcm-ehci.0: BRCM EHCI
brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-1)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI
brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus number 2
brcm-ehci-1 brcm-ehci-1.1: irq 57, io mem 0x10480500
brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
 - Resetting at b0480408
<-- brcm_start_hc
brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 3
brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
 - Resetting at b0480608
<-- brcm_start_hc
brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 4
brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480600
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver catc
drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
usbcore: registered new driver kaweth
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
usbcore: registered new driver rtl8150
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver gl620a
usbcore: registered new driver net1080
usbcore: registered new driver plusb
usbcore: registered new driver rndis_host
usbcore: registered new driver cdc_subset
usbcore: registered new driver zaurus
usbcore: registered new driver iforce
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Freeing unused kernel memory: 3724k freed

init started: BusyBox v1.11.1 (2011-01-09 11:19:55 CST)

starting pid 1, tty : '/etc/init.d/rcS'
Mount /proc fs
Mount /sys fs
Mount /dev/pts
Mount /proc/bus/usb
Cleaning up utmp and wtmp
Start syslog daemon
Configure Network interface
start services
telnetd: starting
  port: 23; interface: any; login program: /bin/login
start user services
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x0 and ending at 0x200000...
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x0 and ending at 0x200000...
#################### boot chain 1 ####################
rtusb init --->
usbcore: registered new driver rt2870
mice: PS/2 mouse device common for all mice
ADDRCONF(NETDEV_UP): eth0: link is not ready
modprobe: module scsi_mod not found
modprobe: failed to load module scsi_mod
modprobe: module sd_mod not found
modprobe: failed to load module sd_mod
modprobe: module fat not found
modprobe: failed to load module fat
modprobe: module vfat not found
modprobe: failed to load module vfat
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
yaffs: dev is 32505860 name is "mtdblock4"
yaffs: Attempting MTD mount on 31.4, "mtdblock4"
yaffs: restored from checkpoint
yaffs: dev is 32505868 name is "mtdblock12"
yaffs: Attempting MTD mount on 31.12, "mtdblock12"
yaffs: restored from checkpoint
yaffs: dev is 32505869 name is "mtdblock13"
yaffs: Attempting MTD mount on 31.13, "mtdblock13"
yaffs: restored from checkpoint


/***********************dare daemon start***********************/

killall: remote_server: no process killed
rmmod: bcmdriver: No such file or directory
rmmod: nexus: No such file or directory
bcmdriver: module license 'Proprietary' taints kernel.
---------------get broadcom driver
*** splash elapse time: 8619(micro seconds) ***
BCMDRV: Initializing bcmdriver version $ 12 $
BCMDRV: Using Interrupt Definition for 7405d0-smp (uname -a)
BCMDRV: Total intc words=3,Total Irqs=97
BCMDRV: Global Interrupt Mask 0:0xD3DF7FFF,1:0x1CBF95F3,2:0x00000008,3:0x00000000
BCMDRV: Initialization complete...
*************liqf sata_close success**********************
--set default passthrough flag, g_passThroughInit:1, g_passThroughON:1 
### 00.01.700: *****************Öмä¼þ°æ±¾ÐÅÏ¢**************
### 00.01.700: **
### 00.01.700: ** ±àÒëʱ¼ä:Mar  9 2011  13:48:50
### 00.01.700: **
### 00.01.700: ** °æ±¾ºÅ:      00.00.00.01
### 00.01.700: **
### 00.01.700: *****************************************************
DareSTB_net_get_ipaddr ioctl: No such device
DareSTB_net_get_ipaddr ioctl: Cannot assign requested address
dg_mw_upgrade_uninit
FFFFFFFFFFFFFFFFFF ipanel_porting_sound_init 899

# cat /proc/cpuinfo
system type             : BCM97xxx Settop Platform
build target            : 7405d0-smp-nand
processor               : 0
cpu model               : BMIPS4380 V4.4  FPU V0.1
cpu MHz                 : 402.43
BogoMIPS                : 402.43    ( udelay_val : 201216  HZ = 1000 )
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : no
ASEs implemented        : mips16
VCED exceptions         : not available
VCEI exceptions         : not available
RAC setting             : Unknown
unaligned access        : 7
rdhwr/brdhwr traps      : 0 / 0
process migrations      : 430
processor               : 1
cpu model               : BMIPS4380 V4.4  FPU V0.1
cpu MHz                 : 404.48
BogoMIPS                : 404.48    ( udelay_val : 202240  HZ = 1000 )
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : no
ASEs implemented        : mips16
VCED exceptions         : not available
VCEI exceptions         : not available
RAC setting             : Unknown
  • MTD分区
-rwxr-xr-x    1 root     root      2097152 Feb  2 06:27 mtdblock0.bin
-rwxr-xr-x    1 root     root      1048576 Feb  2 06:27 mtdblock1.bin
-rwxr-xr-x    1 root     root      2097152 Feb  2 06:27 mtdblock2.bin
-rwxr-xr-x    1 root     root      4194304 Feb  2 06:27 mtdblock3.bin
-rwxr-xr-x    1 root     root      4194304 Feb  2 06:27 mtdblock4.bin
-rwxr-xr-x    1 root     root      2097152 Feb  2 06:27 mtdblock5.bin
-rwxr-xr-x    1 root     root      2097152 Feb  2 06:27 mtdblock6.bin
-rwxr-xr-x    1 root     root      8388608 Feb  2 06:28 mtdblock7.bin
-rwxr-xr-x    1 root     root      8388608 Feb  2 06:28 mtdblock8.bin
-rwxr-xr-x    1 root     root     62914560 Feb  2 06:28 mtdblock9.bin
-rwxr-xr-x    1 root     root     62914560 Feb  2 06:30 mtdblock10.bin
-rwxr-xr-x    1 root     root     20971520 Feb  2 06:39 mtdblock11.bin
-rwxr-xr-x    1 root     root      8388608 Feb  2 06:40 mtdblock12.bin
-rwxr-xr-x    1 root     root     75497472 Feb  2 06:43 mtdblock13.bin

    flash0.data  New NAND flash at 10000000 offset 00000000 size 102400KB
    flash0.app1  New NAND flash at 10000000 offset 06400000 size 61440KB
    flash0.app0  New NAND flash at 10000000 offset 0A000000 size 61440KB
 flash0.kernel1  New NAND flash at 10000000 offset 0DC00000 size 8192KB
 flash0.kernel0  New NAND flash at 10000000 offset 0E400000 size 8192KB
flash0.osflags0  New NAND flash at 10000000 offset 0EC00000 size 2048KB
flash0.osflags1  New NAND flash at 10000000 offset 0EE00000 size 2048KB
  flash0.config  New NAND flash at 10000000 offset 0F000000 size 4096KB
  flash0.splash  New NAND flash at 10000000 offset 0F400000 size 4096KB
   flash0.nvram  New NAND flash at 10000000 offset 0F800000 size 2048KB
  flash0.macadr  New NAND flash at 10000000 offset 0FA00000 size 2048KB
     flash0.cfe  New NAND flash at 10000000 offset 0FC00000 size 2048KB
 flash0.virtual  New NAND flash at 10000000 offset 0FE00000 size 1024KB
 flash0.kreserv  New NAND flash at 10000000 offset 0FF00000 size 1024KB

0x0000000000000000-0x0000000000200000 : "cfe"
0x0000000000400000-0x0000000000500000 : "nvm"
0x0000000000600000-0x0000000000800000 : "macadr"
0x0000000000800000-0x0000000000c00000 : "splash"
0x0000000000c00000-0x0000000001000000 : "config"
0x0000000001000000-0x0000000001200000 : "osflags0"
0x0000000001200000-0x0000000001400000 : "osflags1"
0x0000000001400000-0x0000000001c00000 : "kernel0"
0x0000000001c00000-0x0000000002400000 : "kernel1"
0x0000000002400000-0x0000000006000000 : "app0"
0x0000000006000000-0x0000000009c00000 : "app1"
0x0000000009c00000-0x000000000b000000 : "game"
0x000000000b000000-0x000000000b800000 : "resource"
0x000000000b800000-0x0000000010000000 : "swap"